Eaton Powerware 9390 Specifications Page 50
- Page / 146
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installing the IAC
3-30
EATON Powerware
®
9390 IAC-B and IAC-T Installation and Operation Manual S 164201590 Rev C powerware.com
3.4.5 Installing IAC MBP and MOB TB1 Interface Connections
NOTE When installing control wiring (such as MBP and MOB auxiliary contacts) to
the IAC interface terminals, conduit must be installed between the the UPS cabinet or
device and the IAC, if wiring cannot be run through line-up-and-match cabinets. Install
the control wiring in separate conduit fr om the power wiring.
1. Verify the UPS system is turned off and all power sources are removed. Refer to
the applicable Powerware 9390 Installation and Operation manual, listed in
paragraph 1.5, for shutdown instructions.
2. If not already open, unfasten the IAC front door latch and swing the door open.
3. If not already removed, remove the door. Remove the retaining screws located
inside the door at the top and bottom hinge pivot points, then lift the door off.
Save the retaining screws for reinstallation of the door.
4. If not already removed, remove the screws securing the internal safety shield
panels, and remove the panels to gain access to the terminals.
5. To locate the appropriate terminals, and for wiring and termination requirements,
see Drawing 164201590-7, starting on page A-56, and refer to the applicable
Powerware 9390 Installation and Operation manual, listed in paragraph 1.5, for
UPS cabinet terminal locations.
6. Route and connect the MBP and MOB monitoring auxiliary contact wiring from the
IAC to the UPMs.
7. Route and connect the CAN and backup control (pull chain) auxiliary contact
wiring from the IAC to the UPMs.
8. When all wiring is complete, reinstall the safety shield panels removed in previous
steps.
9. Reinstall the door removed in previous steps and secure with the retained
hardware.
10. Close the door and secure the latch.
- IMPORTANT SAFETY INSTRUCTIONS 2
- SAVE THESE INSTRUCTIONS 2
- Consignes de sécurité 2
- Table of Contents 3
- Section II – Operation 4
- List of Figures 7
- Chapter 1 Introduction 9
- Introduction 10
- EATON Powerware 10
- 1.2 Using This Manual 11
- 1.4 Safety Warnings 13
- 1.5 For More Information 14
- 1.6 Getting Help 14
- Section I Installation 15
- 2.2 Preparing the Site 17
- UPS and IAC 18
- Chapter 3 Installing the IAC 21
- Installing the IAC 22
- FRONT VIEW 23
- REAR VIEW 24
- UPM 1 UPM 2IAC 37
- 3.5 Initial Startup 51
- Installation Checklist 52
- Section II Operation 55
- 4.1.1 UPS Mode 57
- 4.1.2 Maintenance Bypass Mode 58
- 4.2.1 Redundant Operation 59
- MBP is open 60
- Understanding IAC Operation 61
- 5.1 IAC Standard Features 63
- 5.2 Options 64
- 5.3 Symbols 65
- 5.4 IAC Controls 66
- . The input and output 72
- Maintenance Bypass 73
- Chapter 6 Maintaining the IAC 75
- 6.3 Short Circuits 76
- 6.4 Recycling the U sed IAC 76
- 6.5 Maintenance Training 76
- 7.1 Model Number 77
- 7.2 IAC Input 77
- 7.3 IAC Output 77
- Product Specifications 78
- Appendix A 79
- BATTERY CABINET 80
- 40-80 kVA 80
- UPS CABINET 80
- 100-160 kVA 81
- (BATTERY CABINETS NOT SHOWN) 82
- SERIAL NUMBER SEVENTH 87
- DIGITAT“A” 87
- AT “B” or HIGHER 88
- DIGITAT“B”ORHIGHER 89
- TYPICAL1+1PARALLELREDUNDANT 96
- Installation Information 102
- EATON Powerwar e 102
- DESCRIPTION: 103
- DRAWING NO: SHEET: 103
- REVISION: 103
- BOTTOM VIEW 110
- TOP VIEW 110
- LEFT SIDE VIEW 111
- RIGHT SIDE VIEW 111
- 40/40 kVA 208V/208V 118
- 40/40 kVA 480V/480V 119
- MIS AND MBP TERMINAL DETAIL 120
- RIBANDBIBTERMINALDETAIL 121
- BIB TERMINAL DETAIL 122
- 164201590---6 123
- IAC POWER TERMINAL LOCATIONS 123
- 12 of 22 123
- A-45EATON Powerwar e 123
- SLB TERMINAL DETAIL 124
- MAINTENANCE BYPASS 125
- 18 of 22 129
- A-51EATON Powerwar e 129
- TERMINAL LOCA TIONS 136
- IAC TERMINAL TB1 137
- TWISTED PAIR 138
- 1+1 PARALLEL REDUNDANT 139
- CONFIGURATION 139
- BACKUP CONTROL 139
- (PULL CHAIN) WIRING 139
- MAINTENANCE BYPASS AND 140
- MOB MONITORING WIRING 140
- FRONT VIEW RIGHT SIDE VIEW 141
- Warranty 143
- *164201590C* 146
Related products and manuals for Uninterruptible power supplies (UPSs) Eaton Powerware 9390
(17 pages)
(84 pages)© 2020, manymanuals.com. All rights reserved. | 0.125 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals