Eaton Powerware 9390 Specifications Page 73
- Page / 146
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
IAC Features, Options, Controls, and Operation
5-11
EATON Powerware
®
9390 IAC-B and IAC-T Installation and Operation Manual S 164201590 Rev C powerware.com
8. Transfer the UPS to Normal mode by pressing the CONTROL S button on the main
menu bar. The System Controls screen appears.
9. Press the NORMAL button on the System Controls menu bar.
The UPS transfers to Normal mode. If the power processor is not available, the
system remains on bypass and an alarm sounds.
10. Verify that the BYPASS status indicator is illuminated, indicating the UPS is
operating in Bypass mode.
11. Close the front door and secure the latch.
5.6 IAC Operation – Parallel Redundant Configuration
1. Unfasten the IAC front door latch and swing the door open.
2. Verify that the IAC circuit breakers are set as follows:
IAC Module Output Breaker 1 (MOB 1)
CLOSED
IAC Module Output Breaker 2 (MOB 2)
CLOSED
IAC System Load Breaker (SLB) (if installed)
CLOSED
3. Start the UPS in Normal mode according to the Multiple Module Parallel
Operation instructions in the operation chapter of the applicable Powerware 9390
Installation and Operation manual, listed in paragraph 1.5.
4. Close the front door and secure the latch.
5.7 IAC Operation – Parallel Redundant Configuration with
Maintenance Bypass
1. Unfasten the IAC front door latch and swing the door open.
2. Verify that the IAC circuit breakers are set as follows:
IAC Module Output Breaker 1 (MOB 1)
CLOSED
IAC Module Output Breaker 2 (MOB 2)
CLOSED
IAC Maintenance Bypass Switch (MBP)
OPEN
IAC Maintenance Isolation Switch (MIS)
CLOSED
3. Start the UPS in Normal mode according to the Multiple Module Parallel
Operation instructions in the operation chapter of the applicable Powerware 9390
Installation and Operation manual, listed in paragraph 1.5.
4. Close the front door and secure the latch.
5. To transfer the UPS to maintenance b ypass, see paragraph 5.5.2.
To transfer the UPS from maintenance bypass, see paragraph 5.5.3.
- IMPORTANT SAFETY INSTRUCTIONS 2
- SAVE THESE INSTRUCTIONS 2
- Consignes de sécurité 2
- Table of Contents 3
- Section II – Operation 4
- List of Figures 7
- Chapter 1 Introduction 9
- Introduction 10
- EATON Powerware 10
- 1.2 Using This Manual 11
- 1.4 Safety Warnings 13
- 1.5 For More Information 14
- 1.6 Getting Help 14
- Section I Installation 15
- 2.2 Preparing the Site 17
- UPS and IAC 18
- Chapter 3 Installing the IAC 21
- Installing the IAC 22
- FRONT VIEW 23
- REAR VIEW 24
- UPM 1 UPM 2IAC 37
- 3.5 Initial Startup 51
- Installation Checklist 52
- Section II Operation 55
- 4.1.1 UPS Mode 57
- 4.1.2 Maintenance Bypass Mode 58
- 4.2.1 Redundant Operation 59
- MBP is open 60
- Understanding IAC Operation 61
- 5.1 IAC Standard Features 63
- 5.2 Options 64
- 5.3 Symbols 65
- 5.4 IAC Controls 66
- . The input and output 72
- Maintenance Bypass 73
- Chapter 6 Maintaining the IAC 75
- 6.3 Short Circuits 76
- 6.4 Recycling the U sed IAC 76
- 6.5 Maintenance Training 76
- 7.1 Model Number 77
- 7.2 IAC Input 77
- 7.3 IAC Output 77
- Product Specifications 78
- Appendix A 79
- BATTERY CABINET 80
- 40-80 kVA 80
- UPS CABINET 80
- 100-160 kVA 81
- (BATTERY CABINETS NOT SHOWN) 82
- SERIAL NUMBER SEVENTH 87
- DIGITAT“A” 87
- AT “B” or HIGHER 88
- DIGITAT“B”ORHIGHER 89
- TYPICAL1+1PARALLELREDUNDANT 96
- Installation Information 102
- EATON Powerwar e 102
- DESCRIPTION: 103
- DRAWING NO: SHEET: 103
- REVISION: 103
- BOTTOM VIEW 110
- TOP VIEW 110
- LEFT SIDE VIEW 111
- RIGHT SIDE VIEW 111
- 40/40 kVA 208V/208V 118
- 40/40 kVA 480V/480V 119
- MIS AND MBP TERMINAL DETAIL 120
- RIBANDBIBTERMINALDETAIL 121
- BIB TERMINAL DETAIL 122
- 164201590---6 123
- IAC POWER TERMINAL LOCATIONS 123
- 12 of 22 123
- A-45EATON Powerwar e 123
- SLB TERMINAL DETAIL 124
- MAINTENANCE BYPASS 125
- 18 of 22 129
- A-51EATON Powerwar e 129
- TERMINAL LOCA TIONS 136
- IAC TERMINAL TB1 137
- TWISTED PAIR 138
- 1+1 PARALLEL REDUNDANT 139
- CONFIGURATION 139
- BACKUP CONTROL 139
- (PULL CHAIN) WIRING 139
- MAINTENANCE BYPASS AND 140
- MOB MONITORING WIRING 140
- FRONT VIEW RIGHT SIDE VIEW 141
- Warranty 143
- *164201590C* 146
Related products and manuals for Uninterruptible power supplies (UPSs) Eaton Powerware 9390
(17 pages)
(84 pages)© 2020, manymanuals.com. All rights reserved. | 0.250 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals