Eaton Powerware 9390 Specifications Page 102
- Page / 146
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
POWER WIRING INSTALLATION NOTES
013106B
164201590---4 6 of 13
DESCRIPTION:
DATE:
DRAWING NO: SHEET:
REVISION:
Installation Information
A-24 EATON Powerwar e
®
9390 IAC-B and IAC-T Installation and Operation Manual S 164201590 Rev C powerware.com
Read and understand the following notes while planning and performing the installation:
1. Refer to national and local electrical codes for acceptable external wiring practices.
2. Material and labor for external wiring requirements are to be provided by designated
personnel.
CAUTION
Specified wiring and the MOB and SLB breakers for the IAC are rated for parallel
redundant service only. DO NOT use as a parallel capacity system.
CAUTION
Parallel system wiring length should be in accordance with the parallel drawings found in
the appendix of the applicable Powerware 9390 Installation and Operation manual, listed
in paragraph 1.5. Correct wire length
ensures approximate equal current sharing when in
static bypass mode.
3. For external input wiring, use 90°C copper wire. See the appropriate column in Table D
through Table I. Wire sizes are based on using the specified breakers.
4. Wire ampacities are chosen from Table 310---16 of the NEC. Input wire is 90°C
specification.
5. If a BIB is not installed, a minimum of two separate feeds with upstream feeder breakers,
or one feed with two upstream feeder breakers, must be provided: one for the UPS and
one for the IAC bypass input. DO NOT use one feed or a single feeder breaker to supply
both the UPS and IAC.
6. Refer to Section I of this manual for installation instructions.
7. Refer to the applicable Powerware 9390 UPS Installation and Operation manual, listed in
paragraph 1.5, for UPS cabinet wiring requirements, and conduit and terminal locations.
8. Refer to the applicable Powerware 9390 UPS Installation and Operation manual, listed in
paragraph 1.5, for parallel system power and control wiring requirements.
9. Terminals are UL and CSA rated at 90˚C. Refer to Table J through Table Q for power cable
terminations. Drawing 164201590---6 shows the location of the power cable terminals
inside the UPS cabinet.
10. 40 kVA model must be wired for 50 kVA. 100 kVA model must be wired for 120 kVA.
11. Per NEC article 300-20(a), all three-phaseconductorsmustberuninthesameconduit.
Neutral and ground must be run in the same conduit as the phase conductors.
12. Conduit is to be sized to accommodate one neutral conductor the same size as the phase
conductor and one #8 AWG ground conductor. If two neutral conductors or an oversized
neutral conductor are to be installed, size the conduit to accommodate the extra wire or
size. All Powerware 9390 products can accommodate a double-sized neutral.
- IMPORTANT SAFETY INSTRUCTIONS 2
- SAVE THESE INSTRUCTIONS 2
- Consignes de sécurité 2
- Table of Contents 3
- Section II – Operation 4
- List of Figures 7
- Chapter 1 Introduction 9
- Introduction 10
- EATON Powerware 10
- 1.2 Using This Manual 11
- 1.4 Safety Warnings 13
- 1.5 For More Information 14
- 1.6 Getting Help 14
- Section I Installation 15
- 2.2 Preparing the Site 17
- UPS and IAC 18
- Chapter 3 Installing the IAC 21
- Installing the IAC 22
- FRONT VIEW 23
- REAR VIEW 24
- UPM 1 UPM 2IAC 37
- 3.5 Initial Startup 51
- Installation Checklist 52
- Section II Operation 55
- 4.1.1 UPS Mode 57
- 4.1.2 Maintenance Bypass Mode 58
- 4.2.1 Redundant Operation 59
- MBP is open 60
- Understanding IAC Operation 61
- 5.1 IAC Standard Features 63
- 5.2 Options 64
- 5.3 Symbols 65
- 5.4 IAC Controls 66
- . The input and output 72
- Maintenance Bypass 73
- Chapter 6 Maintaining the IAC 75
- 6.3 Short Circuits 76
- 6.4 Recycling the U sed IAC 76
- 6.5 Maintenance Training 76
- 7.1 Model Number 77
- 7.2 IAC Input 77
- 7.3 IAC Output 77
- Product Specifications 78
- Appendix A 79
- BATTERY CABINET 80
- 40-80 kVA 80
- UPS CABINET 80
- 100-160 kVA 81
- (BATTERY CABINETS NOT SHOWN) 82
- SERIAL NUMBER SEVENTH 87
- DIGITAT“A” 87
- AT “B” or HIGHER 88
- DIGITAT“B”ORHIGHER 89
- TYPICAL1+1PARALLELREDUNDANT 96
- Installation Information 102
- EATON Powerwar e 102
- DESCRIPTION: 103
- DRAWING NO: SHEET: 103
- REVISION: 103
- BOTTOM VIEW 110
- TOP VIEW 110
- LEFT SIDE VIEW 111
- RIGHT SIDE VIEW 111
- 40/40 kVA 208V/208V 118
- 40/40 kVA 480V/480V 119
- MIS AND MBP TERMINAL DETAIL 120
- RIBANDBIBTERMINALDETAIL 121
- BIB TERMINAL DETAIL 122
- 164201590---6 123
- IAC POWER TERMINAL LOCATIONS 123
- 12 of 22 123
- A-45EATON Powerwar e 123
- SLB TERMINAL DETAIL 124
- MAINTENANCE BYPASS 125
- 18 of 22 129
- A-51EATON Powerwar e 129
- TERMINAL LOCA TIONS 136
- IAC TERMINAL TB1 137
- TWISTED PAIR 138
- 1+1 PARALLEL REDUNDANT 139
- CONFIGURATION 139
- BACKUP CONTROL 139
- (PULL CHAIN) WIRING 139
- MAINTENANCE BYPASS AND 140
- MOB MONITORING WIRING 140
- FRONT VIEW RIGHT SIDE VIEW 141
- Warranty 143
- *164201590C* 146
Related products and manuals for Uninterruptible power supplies (UPSs) Eaton Powerware 9390
(17 pages)
(84 pages)© 2020, manymanuals.com. All rights reserved. | 0.308 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals