Eaton Powerware 9390 Specifications Page 45
- Page / 146
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installing the IAC
3-25
EATON Powerware
®
9390 IAC-B and IAC-T Installation and Operation Manual S 164201590 Rev C powerware.com
9. If wiring an IAC with an SLB, proceed to Step 10; if wiring an IAC without an SLB,
proceed to Step 13.
10. Route the output cables from the critical load to the IAC SLB output terminals. See
Drawing 164201590-6, starting on page A-34, for IAC wiring access information
and terminal locations.
11. Connect phase A, B, and C, and, if required, Neutral power wiring from the IAC
SLB output terminals to the critical load.
12. Proceed to Step 21.
13. If wiring an IAC with an MBP and MIS, proceed to Step 17; otherwise, proceed to
Step 14.
14. Route the output cables to the IAC MOB 1 output terminals. See Drawing
164201590-6, starting on page A-34, for IAC wiring access information and
terminal locations.
15. Connect phase A, B, and C, and, if required, Neutral power wiring from the IAC
MOB 1 output terminals to the critical load.
16. Proceed to Step 21.
17. Route the bypass input cables to the IAC MBP bypass input terminals. See Drawing
164201590-6, starting on page A-34, for IAC wiring access information and
terminal locations.
18. Connect phase A, B, and C, and, if required, Neutral bypass input power wiring
from the s ource to the IAC MBP bypass terminals.
19. Route the output cables from the critical load to the IAC MIS output terminals.
See Drawing 164201590-6, starting on page A-34, for IAC wiring access information
and terminal locations.
20. Connect phase A, B, and C, and, if required, Neutral power wiring from the IAC
MIS output terminals to the critical load.
21. After wiring the UPS system to the facility power and critical load, be sure to
ground the system according to local and/or national electrical wiring codes.
22. If wiring interface connections, proceed to paragraph 3.4.5; otherwise, proceed to
Step 23.
23. When all wiring is complete, reinstall the safety shield panels removed in previous
steps.
24. Reinstall the door removed in previous steps and secure with the retained
hardware.
25. Close the door and secure the latch.
- IMPORTANT SAFETY INSTRUCTIONS 2
- SAVE THESE INSTRUCTIONS 2
- Consignes de sécurité 2
- Table of Contents 3
- Section II – Operation 4
- List of Figures 7
- Chapter 1 Introduction 9
- Introduction 10
- EATON Powerware 10
- 1.2 Using This Manual 11
- 1.4 Safety Warnings 13
- 1.5 For More Information 14
- 1.6 Getting Help 14
- Section I Installation 15
- 2.2 Preparing the Site 17
- UPS and IAC 18
- Chapter 3 Installing the IAC 21
- Installing the IAC 22
- FRONT VIEW 23
- REAR VIEW 24
- UPM 1 UPM 2IAC 37
- 3.5 Initial Startup 51
- Installation Checklist 52
- Section II Operation 55
- 4.1.1 UPS Mode 57
- 4.1.2 Maintenance Bypass Mode 58
- 4.2.1 Redundant Operation 59
- MBP is open 60
- Understanding IAC Operation 61
- 5.1 IAC Standard Features 63
- 5.2 Options 64
- 5.3 Symbols 65
- 5.4 IAC Controls 66
- . The input and output 72
- Maintenance Bypass 73
- Chapter 6 Maintaining the IAC 75
- 6.3 Short Circuits 76
- 6.4 Recycling the U sed IAC 76
- 6.5 Maintenance Training 76
- 7.1 Model Number 77
- 7.2 IAC Input 77
- 7.3 IAC Output 77
- Product Specifications 78
- Appendix A 79
- BATTERY CABINET 80
- 40-80 kVA 80
- UPS CABINET 80
- 100-160 kVA 81
- (BATTERY CABINETS NOT SHOWN) 82
- SERIAL NUMBER SEVENTH 87
- DIGITAT“A” 87
- AT “B” or HIGHER 88
- DIGITAT“B”ORHIGHER 89
- TYPICAL1+1PARALLELREDUNDANT 96
- Installation Information 102
- EATON Powerwar e 102
- DESCRIPTION: 103
- DRAWING NO: SHEET: 103
- REVISION: 103
- BOTTOM VIEW 110
- TOP VIEW 110
- LEFT SIDE VIEW 111
- RIGHT SIDE VIEW 111
- 40/40 kVA 208V/208V 118
- 40/40 kVA 480V/480V 119
- MIS AND MBP TERMINAL DETAIL 120
- RIBANDBIBTERMINALDETAIL 121
- BIB TERMINAL DETAIL 122
- 164201590---6 123
- IAC POWER TERMINAL LOCATIONS 123
- 12 of 22 123
- A-45EATON Powerwar e 123
- SLB TERMINAL DETAIL 124
- MAINTENANCE BYPASS 125
- 18 of 22 129
- A-51EATON Powerwar e 129
- TERMINAL LOCA TIONS 136
- IAC TERMINAL TB1 137
- TWISTED PAIR 138
- 1+1 PARALLEL REDUNDANT 139
- CONFIGURATION 139
- BACKUP CONTROL 139
- (PULL CHAIN) WIRING 139
- MAINTENANCE BYPASS AND 140
- MOB MONITORING WIRING 140
- FRONT VIEW RIGHT SIDE VIEW 141
- Warranty 143
- *164201590C* 146
Related products and manuals for Uninterruptible power supplies (UPSs) Eaton Powerware 9390
(17 pages)
(84 pages)© 2020, manymanuals.com. All rights reserved. | 0.156 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals