Eaton PROFIBUS-DP EZ204-DP User Manual Page 15
- Page / 300
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
For more information visit: www.EatonElectrical.com 11MN05013003E
1EZ
Target readership EZ must only be installed and connected up by trained
electricians or other persons who are familiar with the
installation of electrical equipment.
Specialist electrical training is needed for commissioning and
creating circuit diagrams. When active components such as
motors or pressure cylinders are controlled, parts of the
system can be damaged and persons put at risk if EZ is
connected or programmed incorrectly.
Proper use EZ is a programmable switching and control device and is
used as a replacement for relay and contactor control circuits.
EZ may only be operated when it has been correctly and
properly installed.
• EZ is designed to be installed in an enclosure, switch
cabinet or service distribution board. Both the power feed
and the signal terminals must be laid and covered so as to
prevent accidental contact.
• The installation must comply with regulations for
electromagnetic compatibility (EMC).
• The starting up of EZ should not cause any hazards arising
from controlled devices, such as unexpected motor startups
or power ups.
Improper use
EZ should not be used as a substitute for safety-related
controls such as burner or crane controls, emergency-stop or
two-hand safety controls.
EZ500_700.book Page 11 Tuesday, May 3, 2005 5:15 PM
- 1-888-55-66342 1
- Warning! 3
- Dangerous electrical voltage! 3
- Contents 5
- About This Manual 13
- Overview 16
- ANSI or EZ format 18
- MN05013003E16 20
- EZ xxx-xx-xxx 21
- MN05013003E18 22
- Main menu 23
- EZ500 or EZ700 System 23
- (only on devices with clock) 24
- EZ Status display 24
- Advanced Status display 25
- EZ LED display 25
- Menu structure 26
- MN05013003E24 28
- EZ System menu 29
- DEL and ALT 29
- System menu 30
- YEAR 2004 32
- HH:MM 14:23 32
- DD.MM 17.03 32
- 2Installation 33
- Installation 34
- Mounting 35
- Terminals 37
- MN05013003E38 42
- Connecting the inputs 43
- 100 nF/275 V h 45
- Figure 14: EZ with EZ256-HCI 46
- EZ…-DC-.D 47
- MN05013003E46 50
- MN05013003E48 52
- Connecting the outputs 55
- Connecting relay outputs 56
- EZ512-..-R 56
- EZ7..-..-R.. and EZ202-RE 56
- Connecting transistor outputs 58
- EZ512-..-T 58
- EZ7..-..-T 58
- MN05013003E56 60
- Expanding inputs/outputs 61
- Switching on 65
- 3 Commissioning 65
- Commissioning 66
- EZ operating modes 67
- 69
- MO 02:00 69
- .......STOP 69
- 4 Wiring with EZ 77
- Operation of EZ 79
- MN05013003E76 80
- Relay, function relays 81
- : :1…:8 :1…:8 – 82
- Y Y1…Y8 Y1…Y8 – 82
- Z Z1…Z3 Z1…Z3 – 82
- I2u------ÄQ4 85
- I1 to I2 in the 87
- I3 from make to break 88
- J section 100
- I5-------CC1 101
- I6-------RC1 101
- C1-------TT1 101
- T1-------ÄQ1 101
- Wiring with EZ 102
- Function relays 103
- MN05013003E104 108
- A8-------ÄQ3 113
- First operating state 117
- Counters 119
- MN05013003E116 120
- S 00000 120
- C with setpoint value 122
- = 0.5 × 127
- Contact has not switched 129
- Contact has switched 129
- Actual value (0153) 129
- Text display 139
- Ä, Å, è, ^, ä 139
- D1 to D16 139
- 7-day time switch 145
- Operating hours counter 151
- Timing relays 155
- I1 Time setpoint 1: 155
- MN05013003E152 156
- MN05013003E156 160
- MN05013003E158 162
- MN05013003E160 164
- Timing relay, single pulse 165
- MN05013003E162 166
- :1 to :8 170
- Ä:1 to Ä:8 170
- : of the 171
- Year time switch 173
- Master reset 181
- Basic circuits 183
- Example circuits 191
- Storage positions 192
- PULSE VALUE RESET 192
- 5 EZ Settings 203
- EZ Settings 204
- Password protection 205
- DELETE ? 209
- Changing parameters 211
- XSelect the RULE menu 219
- XPress the OK button 219
- ÍÚ Select required value 221
- Startup behavior 225
- RUN MODE EZ is in STOP mode 226
- RUN MODEå EZ is in RUN mode 226
- Setting the cycle time 229
- 6Inside EZ 235
- Inside EZ 236
- EZ circuit diagram cycle 237
- Figure 87: On and off delays 241
- Expanding EZ700 243
- Figure 89: Remove the cover 247
- Memory card 249
- INVALID PROG 253
- 7 What Happens If ...? 255
- What Happens If ...? 256
- Dimensions 259
- MN05013003E256 260
- Appendix 262
- Technical Data 263
- Available function relays 278
- Names of relays 279
- Names of function relay 279
- Glossary 281
- MN05013003E282 286
- MN05013003E284 288
- MN05013003E286 290
- MN05013003E288 292
- MN05013003E290 294
- MN05013003E292 296
- MN05013003E294 298
Related products and manuals for Networking Eaton PROFIBUS-DP EZ204-DP
Networking Eaton QSNAP User Manual
(11 pages)
(11 pages)
Networking Eaton -66103 User Manual
(12 pages)
(12 pages)
Networking Eaton QSNAP Service Manual
(64 pages)
(64 pages)
Networking Eaton QSNAP User Manual
(14 pages)
(14 pages)
© 2020, manymanuals.com. All rights reserved. | 0.802 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals