Eaton PROFIBUS-DP EZ204-DP User Manual Page 108
- Page / 300
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
For more information visit: www.EatonElectrical.com
Wiring with EZ
MN05013003E104
I1 Comparison value 1 (positive value I7, I8, I11, I12, actual
value T1 to T16, C1 to C16)
F1 Gain factor for I1 (I1 = F1 × actual value at I1);
F1 = positive value from 0 to 9999
I2 Comparison value 2 (positive value I7, I8, I11, I12, actual
value T1 to T16, C1 to C16)
F2 Gain factor for I2 (I2 = F2 × actual value at I2);
F2 = positive value from 0 to 9999
OS Offset for the value of I1 (I1 = OS + + actual value at
I1); OS = positive value from 0 to 9999
HY Switching hysteresis for value I2
Value HY applies both to positive and negative
hysteresis.
•
I2 = Actual value at I2 + HY;
•
I2 = Actual value at I2 - HY;
•
HY= positive value from 0 to 9999
J
Work normally with analog inputs and setpoints as the
parameters for the analog value comparator.
J
The analog value comparator for EZ500 and EZ700
operates internally in the value range:
–2147483648 to +2147483647
This ensures that the correct value is always calculated.
This is important for multiplying values (I1 × F1 or I2 ×
F2).
Example:
I1 = 9999, F1 = 9999
I1 × F1 = 99980001
The result is within the value range.
J
If no value is entered at F1 or F2, only the value at I1 and I2
is used (no multiplication).
EZ500_700.book Page 104 Tuesday, May 3, 2005 5:15 PM
- 1-888-55-66342 1
- Warning! 3
- Dangerous electrical voltage! 3
- Contents 5
- About This Manual 13
- Overview 16
- ANSI or EZ format 18
- MN05013003E16 20
- EZ xxx-xx-xxx 21
- MN05013003E18 22
- Main menu 23
- EZ500 or EZ700 System 23
- (only on devices with clock) 24
- EZ Status display 24
- Advanced Status display 25
- EZ LED display 25
- Menu structure 26
- MN05013003E24 28
- EZ System menu 29
- DEL and ALT 29
- System menu 30
- YEAR 2004 32
- HH:MM 14:23 32
- DD.MM 17.03 32
- 2Installation 33
- Installation 34
- Mounting 35
- Terminals 37
- MN05013003E38 42
- Connecting the inputs 43
- 100 nF/275 V h 45
- Figure 14: EZ with EZ256-HCI 46
- EZ…-DC-.D 47
- MN05013003E46 50
- MN05013003E48 52
- Connecting the outputs 55
- Connecting relay outputs 56
- EZ512-..-R 56
- EZ7..-..-R.. and EZ202-RE 56
- Connecting transistor outputs 58
- EZ512-..-T 58
- EZ7..-..-T 58
- MN05013003E56 60
- Expanding inputs/outputs 61
- Switching on 65
- 3 Commissioning 65
- Commissioning 66
- EZ operating modes 67
- 69
- MO 02:00 69
- .......STOP 69
- 4 Wiring with EZ 77
- Operation of EZ 79
- MN05013003E76 80
- Relay, function relays 81
- : :1…:8 :1…:8 – 82
- Y Y1…Y8 Y1…Y8 – 82
- Z Z1…Z3 Z1…Z3 – 82
- I2u------ÄQ4 85
- I1 to I2 in the 87
- I3 from make to break 88
- J section 100
- I5-------CC1 101
- I6-------RC1 101
- C1-------TT1 101
- T1-------ÄQ1 101
- Wiring with EZ 102
- Function relays 103
- MN05013003E104 108
- A8-------ÄQ3 113
- First operating state 117
- Counters 119
- MN05013003E116 120
- S 00000 120
- C with setpoint value 122
- = 0.5 × 127
- Contact has not switched 129
- Contact has switched 129
- Actual value (0153) 129
- Text display 139
- Ä, Å, è, ^, ä 139
- D1 to D16 139
- 7-day time switch 145
- Operating hours counter 151
- Timing relays 155
- I1 Time setpoint 1: 155
- MN05013003E152 156
- MN05013003E156 160
- MN05013003E158 162
- MN05013003E160 164
- Timing relay, single pulse 165
- MN05013003E162 166
- :1 to :8 170
- Ä:1 to Ä:8 170
- : of the 171
- Year time switch 173
- Master reset 181
- Basic circuits 183
- Example circuits 191
- Storage positions 192
- PULSE VALUE RESET 192
- 5 EZ Settings 203
- EZ Settings 204
- Password protection 205
- DELETE ? 209
- Changing parameters 211
- XSelect the RULE menu 219
- XPress the OK button 219
- ÍÚ Select required value 221
- Startup behavior 225
- RUN MODE EZ is in STOP mode 226
- RUN MODEå EZ is in RUN mode 226
- Setting the cycle time 229
- 6Inside EZ 235
- Inside EZ 236
- EZ circuit diagram cycle 237
- Figure 87: On and off delays 241
- Expanding EZ700 243
- Figure 89: Remove the cover 247
- Memory card 249
- INVALID PROG 253
- 7 What Happens If ...? 255
- What Happens If ...? 256
- Dimensions 259
- MN05013003E256 260
- Appendix 262
- Technical Data 263
- Available function relays 278
- Names of relays 279
- Names of function relay 279
- Glossary 281
- MN05013003E282 286
- MN05013003E284 288
- MN05013003E286 290
- MN05013003E288 292
- MN05013003E290 294
- MN05013003E292 296
- MN05013003E294 298
Related products and manuals for Networking Eaton PROFIBUS-DP EZ204-DP
Networking Eaton QSNAP User Manual
(11 pages)
(11 pages)
Networking Eaton -66103 User Manual
(12 pages)
(12 pages)
Networking Eaton QSNAP Service Manual
(64 pages)
(64 pages)
Networking Eaton QSNAP User Manual
(14 pages)
(14 pages)
© 2020, manymanuals.com. All rights reserved. | 0.710 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals