Eaton 93PM Installation Guide Page 71
- Page / 93
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
P-164000249 30-200 kW 63
Revision 2 User's and Installation Guide
1.
Press the lock button in the upper right corner of the screen.
2. Type your passcode and press OK.
3. You are signed in. Press Continue to return to the previous screen.
There are three attempts to input the password. If an incorrect password is given more than three
times, you need to wait for 30 minutes before trying again.
To modify the user settings, you need to enter level 2 password.
For the default passwords, see Chapter 11 APPENDIX A: User settings on page 84.
6.4 System control instructions
6.4.1 Starting the UPS system in Double conversion mode
The UPS system can consist of a single UPS or several parallel UPSs. UPSs with their MOB open are
not considered as part of the system.
To start the UPS system:
1. Unfasten the front door latch and swing the door open.
2. Verify that rectifier input switches are closed if included inside the UPS system, and verify that
battery breaker is closed, and close the front door.
3. Close the UPS input feeder circuit breaker.
4. Close the UPS bypass input feeder circuit breaker.
5. Observe the UPS control panel display becoming active, indicating logic power.
Repeat steps 1-5 for each individual UPS in the system.
6. Press the Controls button in the main menu. The System Controls screen appears.
7. On the System Controls screen, the system status should indicate SHUTDOWN.
8. Press the Go online button on the System Controls screen. If Auto Bypass is enabled (factory
default), the critical load is immediately supplied by the bypass source, in Bypass mode, until
the inverter turns on and the UPS transfers to double conversion mode. The status indicator on
the UPS control panel indicates the UPS is in Bypass mode. If auto bypass is not enabled, the
UPS output remains off until the UPS system transfers to double conversion mode.
9. Observe the following messages appear sequentially on the System Controls screen:
STARTING
ONLINE
The rectifier and inverter turn on. The DC voltage continues to ramp up to full voltage. Once the
DC link reaches full voltage, and the battery breaker is closed, the UPS output relay K3 closes
and the static switch turns off. Power is now supplied to the Critical load in double conversion
mode. It takes approximately 20 seconds for the UPS system to achieve double conversion
mode.
10. The UPS system is now operating in double conversion mode and the NORMAL status
indicator is illuminated in all UPSs in the system.
- Eaton 93PM UPS P-164000249 1
- 30-200 kW 1
- Eaton 93PM UPS 3
- Contents 5
- List of Figures 7
- List of Tables 8
- 1 Safety instructions 9
- 2 30-200 kW P-164000249 10
- 1.1 Audience 11
- 1.2 CE marking 11
- 1.3 User precautions 12
- 1.4 Environment 12
- P-164000249 30-200 kW 5 13
- 1.7 For more information 14
- P-164000249 30-200 kW 7 15
- 2 Introduction to Eaton UPS 16
- P-164000249 30-200 kW 9 17
- 10 30-200 kW P-164000249 18
- P-164000249 30-200 kW 11 19
- 12 30-200 kW P-164000249 20
- 2.2 UPS operating modes 21
- 14 30-200 kW P-164000249 22
- Internal relay contacts 22
- P-164000249 30-200 kW 15 23
- 2.2.3 Bypass mode 24
- 2.3 UPS features 25
- 2.3.2 Powerware Hot Sync 26
- 2.4.1 Customer interface 26
- 2.5 Options and accessories 27
- 20 30-200 kW P-164000249 28
- 1. Bypass Input Breaker (BIB) 29
- 2.6 Battery system 30
- P-164000249 30-200 kW 23 31
- 24 30-200 kW P-164000249 32
- 3.2 Site preparations 33
- 26 30-200 kW P-164000249 34
- P-164000249 30-200 kW 27 35
- 28 30-200 kW P-164000249 36
- P-164000249 30-200 kW 29 37
- 30 30-200 kW P-164000249 38
- P-164000249 30-200 kW 31 39
- 32 30-200 kW P-164000249 40
- P-164000249 30-200 kW 33 41
- 34 30-200 kW P-164000249 42
- P-164000249 30-200 kW 35 43
- 4 UPS system installation 44
- P-164000249 30-200 kW 37 45
- 38 30-200 kW P-164000249 46
- Top cable access kit 47
- 40 30-200 kW P-164000249 48
- P-164000249 30-200 kW 41 49
- 42 30-200 kW P-164000249 50
- P-164000249 30-200 kW 43 51
- 44 30-200 kW P-164000249 52
- P-164000249 30-200 kW 45 53
- 46 30-200 kW P-164000249 54
- P-164000249 30-200 kW 47 55
- 4.6.1 Power wiring overview 56
- P-164000249 30-200 kW 49 57
- 50 30-200 kW P-164000249 58
- P-164000249 30-200 kW 51 59
- 52 30-200 kW P-164000249 60
- 5 Communication interfaces 61
- 54 30-200 kW P-164000249 62
- P-164000249 30-200 kW 55 63
- 5.3 Signal input monitoring 64
- P-164000249 30-200 kW 57 65
- 6 UPS operating instructions 66
- P-164000249 30-200 kW 59 67
- 6.1.2 Status indicators 68
- 6.2 Steps to operate the UPS 69
- 6.3 Signing in 70
- STARTING 71
- 64 30-200 kW P-164000249 72
- P-164000249 30-200 kW 65 73
- 66 30-200 kW P-164000249 74
- 6.5 UPS control instructions 75
- 6.6 UPM control instructions 76
- P-164000249 30-200 kW 69 77
- 70 30-200 kW P-164000249 78
- Maintenance Bypass 78
- Switch (MBS) 78
- P-164000249 30-200 kW 71 79
- 7 UPS maintenance 80
- 7.2.1 DAILY maintenance 81
- 7.2.2 MONTHLY maintenance 81
- 7.2.3 PERIODIC maintenance 81
- 7.2.4 ANNUAL maintenance 82
- 7.2.5 BATTERY maintenance 82
- 7.4 Maintenance training 83
- 8 Technical data 84
- 8.2 UPS system input 85
- 8.3 UPS system output 85
- 8.4 Battery specification 86
- P-164000249 30-200 kW 79 87
- 80 30-200 kW P-164000249 88
- 9 Warranty 89
- 10 Installation checklist 90
- P-164000249 30-200 kW 83 91
- 11 APPENDIX A: User settings 92
- Setting Description 93
- Table 11-2: Config settings 93
Related products and manuals for Uninterruptible power supplies (UPSs) Eaton 93PM
(146 pages)
(84 pages)© 2020, manymanuals.com. All rights reserved. | 2.249 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals