Eaton 93PM Installation Guide Page 25
- Page / 93
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
P-164000249 30-200 kW 17
Revision 2 User's and Installation Guide
NOTE
The critical load is not protected while the UPS is in Bypass mode.
Internal relay contacts
Figure 2-7: Path of current through the UPS in bypass mode
In bypass mode, the output of the system is provided with three-phase AC power directly from the
system input. While in this mode, the output of the system is not protected from voltage or frequency
fluctuations or power outages from the source. Some power line filtering and transient protection is
provided to the load but no active power conditioning or battery support is available to the output of
the system in the bypass mode of operation.
The static bypass is comprised of a solid-state, silicon-controlled rectifier (SCR) static switch (SSW)
and a backfeed protection isolation device K5. The static switch is rated as a continuous-duty device
that is used anytime the inverter is unable to support the applied load. The static switch is wired in
series with the backfeed protection. The static switch, being an electronically-controlled device, can
be turned on immediately to pick up the load from the inverter without interruption. The backfeed
protection is normally always closed, ready to support the static switch unless the bypass input
source becomes unavailable.
2.3 UPS features
The Eaton UPS has many features that provide cost-effective and consistently reliable power
protection. The feature descriptions provide a brief overview of the UPS standard features.
- Eaton 93PM UPS P-164000249 1
- 30-200 kW 1
- Eaton 93PM UPS 3
- Contents 5
- List of Figures 7
- List of Tables 8
- 1 Safety instructions 9
- 2 30-200 kW P-164000249 10
- 1.1 Audience 11
- 1.2 CE marking 11
- 1.3 User precautions 12
- 1.4 Environment 12
- P-164000249 30-200 kW 5 13
- 1.7 For more information 14
- P-164000249 30-200 kW 7 15
- 2 Introduction to Eaton UPS 16
- P-164000249 30-200 kW 9 17
- 10 30-200 kW P-164000249 18
- P-164000249 30-200 kW 11 19
- 12 30-200 kW P-164000249 20
- 2.2 UPS operating modes 21
- 14 30-200 kW P-164000249 22
- Internal relay contacts 22
- P-164000249 30-200 kW 15 23
- 2.2.3 Bypass mode 24
- 2.3 UPS features 25
- 2.3.2 Powerware Hot Sync 26
- 2.4.1 Customer interface 26
- 2.5 Options and accessories 27
- 20 30-200 kW P-164000249 28
- 1. Bypass Input Breaker (BIB) 29
- 2.6 Battery system 30
- P-164000249 30-200 kW 23 31
- 24 30-200 kW P-164000249 32
- 3.2 Site preparations 33
- 26 30-200 kW P-164000249 34
- P-164000249 30-200 kW 27 35
- 28 30-200 kW P-164000249 36
- P-164000249 30-200 kW 29 37
- 30 30-200 kW P-164000249 38
- P-164000249 30-200 kW 31 39
- 32 30-200 kW P-164000249 40
- P-164000249 30-200 kW 33 41
- 34 30-200 kW P-164000249 42
- P-164000249 30-200 kW 35 43
- 4 UPS system installation 44
- P-164000249 30-200 kW 37 45
- 38 30-200 kW P-164000249 46
- Top cable access kit 47
- 40 30-200 kW P-164000249 48
- P-164000249 30-200 kW 41 49
- 42 30-200 kW P-164000249 50
- P-164000249 30-200 kW 43 51
- 44 30-200 kW P-164000249 52
- P-164000249 30-200 kW 45 53
- 46 30-200 kW P-164000249 54
- P-164000249 30-200 kW 47 55
- 4.6.1 Power wiring overview 56
- P-164000249 30-200 kW 49 57
- 50 30-200 kW P-164000249 58
- P-164000249 30-200 kW 51 59
- 52 30-200 kW P-164000249 60
- 5 Communication interfaces 61
- 54 30-200 kW P-164000249 62
- P-164000249 30-200 kW 55 63
- 5.3 Signal input monitoring 64
- P-164000249 30-200 kW 57 65
- 6 UPS operating instructions 66
- P-164000249 30-200 kW 59 67
- 6.1.2 Status indicators 68
- 6.2 Steps to operate the UPS 69
- 6.3 Signing in 70
- STARTING 71
- 64 30-200 kW P-164000249 72
- P-164000249 30-200 kW 65 73
- 66 30-200 kW P-164000249 74
- 6.5 UPS control instructions 75
- 6.6 UPM control instructions 76
- P-164000249 30-200 kW 69 77
- 70 30-200 kW P-164000249 78
- Maintenance Bypass 78
- Switch (MBS) 78
- P-164000249 30-200 kW 71 79
- 7 UPS maintenance 80
- 7.2.1 DAILY maintenance 81
- 7.2.2 MONTHLY maintenance 81
- 7.2.3 PERIODIC maintenance 81
- 7.2.4 ANNUAL maintenance 82
- 7.2.5 BATTERY maintenance 82
- 7.4 Maintenance training 83
- 8 Technical data 84
- 8.2 UPS system input 85
- 8.3 UPS system output 85
- 8.4 Battery specification 86
- P-164000249 30-200 kW 79 87
- 80 30-200 kW P-164000249 88
- 9 Warranty 89
- 10 Installation checklist 90
- P-164000249 30-200 kW 83 91
- 11 APPENDIX A: User settings 92
- Setting Description 93
- Table 11-2: Config settings 93
Related products and manuals for Uninterruptible power supplies (UPSs) Eaton 93PM
(146 pages)
(84 pages)© 2020, manymanuals.com. All rights reserved. | 1.610 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals