Eaton 93PM Installation Guide Page 42
- Page / 93
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
34 30-200 kW P-164000249
User's and Installation Guide Revision 2
3.2.3 UPS system interface wiring preparation
Control wiring for features and options should be connected at the customer interface terminal blocks
located on top front of the UPS, behind the door.
DANGER
Do not directly connect relay contacts to the mains related circuits. Reinforced insulation to
the mains is required.
Read and understand the following notes while planning and performing the installation:
• All interface wiring is to be provided by the customer.
• When installing internal interface wiring to Mini-slot terminals, route the wiring through the
internal opening in the Mini-slot communication bay.
• All signal inputs or remote features require an isolated normally-open contact or switch (rated at
24 VDC, 20 mA minimum) connected between the alarm input and common terminal. All control
wiring and relay and switch contacts are customer-supplied. Use twisted-pair wires for each
alarm input and common.
• The signal inputs can be programmed to display the alarm functional name.
• LAN and telephone drops for use with Mini-slot cards must be provided by facility planners or
the customer.
• The UPS Battery Aux and 24 VDC Shunt Trip signal wiring from the UPS must be connected to
the DC source disconnect device.
• Battery Aux and 24 VDC Shunt Trip wiring should be a minimum of 1.5 mm².
• The Remote EPO feature opens all switchgear in the UPS cabinet and isolates power from your
critical load. Local electrical codes may also require tripping upstream protective devices to the
UPS.
• The Remote EPO switch must be a dedicated switch not tied to any other circuits.
• A jumper wire must be connected between pins 1 and 2 on connector EPO, if the normally-
closed (NC) Remote EPO contact is used.
• Remote EPO wiring should be a minimum of 0.75 mm² and a maximum of 2.5 mm².
• The maximum distance between the Remote EPO and the UPS cannot exceed 150 meters.
• Alarm relay contacts have a maximum current rating of 5 A and a switched voltage rating of 30
VAC (RMS) and 30 VDC.
• Alarm relay wiring should be a minimum of 0.75 mm².
3.3 Unpacking and unloading the UPS
If the equipment has been transported in the upright position the outside ’Tip&Tell’ indicator on the
package surface should be intact. If the arrow has turned all blue, contact the appropriate parties for
reporting inappropriate transportation.
- Eaton 93PM UPS P-164000249 1
- 30-200 kW 1
- Eaton 93PM UPS 3
- Contents 5
- List of Figures 7
- List of Tables 8
- 1 Safety instructions 9
- 2 30-200 kW P-164000249 10
- 1.1 Audience 11
- 1.2 CE marking 11
- 1.3 User precautions 12
- 1.4 Environment 12
- P-164000249 30-200 kW 5 13
- 1.7 For more information 14
- P-164000249 30-200 kW 7 15
- 2 Introduction to Eaton UPS 16
- P-164000249 30-200 kW 9 17
- 10 30-200 kW P-164000249 18
- P-164000249 30-200 kW 11 19
- 12 30-200 kW P-164000249 20
- 2.2 UPS operating modes 21
- 14 30-200 kW P-164000249 22
- Internal relay contacts 22
- P-164000249 30-200 kW 15 23
- 2.2.3 Bypass mode 24
- 2.3 UPS features 25
- 2.3.2 Powerware Hot Sync 26
- 2.4.1 Customer interface 26
- 2.5 Options and accessories 27
- 20 30-200 kW P-164000249 28
- 1. Bypass Input Breaker (BIB) 29
- 2.6 Battery system 30
- P-164000249 30-200 kW 23 31
- 24 30-200 kW P-164000249 32
- 3.2 Site preparations 33
- 26 30-200 kW P-164000249 34
- P-164000249 30-200 kW 27 35
- 28 30-200 kW P-164000249 36
- P-164000249 30-200 kW 29 37
- 30 30-200 kW P-164000249 38
- P-164000249 30-200 kW 31 39
- 32 30-200 kW P-164000249 40
- P-164000249 30-200 kW 33 41
- 34 30-200 kW P-164000249 42
- P-164000249 30-200 kW 35 43
- 4 UPS system installation 44
- P-164000249 30-200 kW 37 45
- 38 30-200 kW P-164000249 46
- Top cable access kit 47
- 40 30-200 kW P-164000249 48
- P-164000249 30-200 kW 41 49
- 42 30-200 kW P-164000249 50
- P-164000249 30-200 kW 43 51
- 44 30-200 kW P-164000249 52
- P-164000249 30-200 kW 45 53
- 46 30-200 kW P-164000249 54
- P-164000249 30-200 kW 47 55
- 4.6.1 Power wiring overview 56
- P-164000249 30-200 kW 49 57
- 50 30-200 kW P-164000249 58
- P-164000249 30-200 kW 51 59
- 52 30-200 kW P-164000249 60
- 5 Communication interfaces 61
- 54 30-200 kW P-164000249 62
- P-164000249 30-200 kW 55 63
- 5.3 Signal input monitoring 64
- P-164000249 30-200 kW 57 65
- 6 UPS operating instructions 66
- P-164000249 30-200 kW 59 67
- 6.1.2 Status indicators 68
- 6.2 Steps to operate the UPS 69
- 6.3 Signing in 70
- STARTING 71
- 64 30-200 kW P-164000249 72
- P-164000249 30-200 kW 65 73
- 66 30-200 kW P-164000249 74
- 6.5 UPS control instructions 75
- 6.6 UPM control instructions 76
- P-164000249 30-200 kW 69 77
- 70 30-200 kW P-164000249 78
- Maintenance Bypass 78
- Switch (MBS) 78
- P-164000249 30-200 kW 71 79
- 7 UPS maintenance 80
- 7.2.1 DAILY maintenance 81
- 7.2.2 MONTHLY maintenance 81
- 7.2.3 PERIODIC maintenance 81
- 7.2.4 ANNUAL maintenance 82
- 7.2.5 BATTERY maintenance 82
- 7.4 Maintenance training 83
- 8 Technical data 84
- 8.2 UPS system input 85
- 8.3 UPS system output 85
- 8.4 Battery specification 86
- P-164000249 30-200 kW 79 87
- 80 30-200 kW P-164000249 88
- 9 Warranty 89
- 10 Installation checklist 90
- P-164000249 30-200 kW 83 91
- 11 APPENDIX A: User settings 92
- Setting Description 93
- Table 11-2: Config settings 93
Related products and manuals for Uninterruptible power supplies (UPSs) Eaton 93PM
(146 pages)
(84 pages)© 2020, manymanuals.com. All rights reserved. | 1.077 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals