Eaton 93PM Installation Guide Page 30
- Page / 93
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
22 30-200 kW P-164000249
User's and Installation Guide Revision 2
2.5.2 Top air exhaust kit
The top air exhaust kit is used to direct the UPS cooling air front-to-top. The kit will eliminate the
cooling clearance requirement from the back of the unit, and enable installing the 93PM UPS even
against a wall, in a corner or back-to-back. The kit increases the depth of the unit by 200 mm.
Refer to Chapter 3.2 Site preparations on page 25 for further information.
2.5.3 Top cable access kit
The top cable access kit is designed to support top cabling to the 30-150 kW 93PM UPS in sites
where the cabling is distributed through overhead cable trays. The kit is installed at the right hand side
of the UPS unit.
The 200 kW 93PM UPS does not require this kit, since the unit supports bottom, rear, and top cable
entry by standard.
Refer to Chapter 3.2 Site preparations on page 25 and Chapter 4.1 Steps to install the UPS on
page 36 for further information.
See also Figure 4-4: 93PM 30-150 kW Top cable access kit on page 40.
2.5.4 Field Installed UPM
A Field Installed UPM (FI-UPM) can be installed in the cabinet any time in the future when power
needs change. This enables the UPS system to grow with the business, thus lowering the initial
investment required for the system Day1.
In order to install an FI-UPM, the UPS cabinet needs to have upgradeability, which is determined by
the power rating of the static bypass. For example, if the static bypass is rated for 150 kW, the fourth
UPM cannot be installed into the frame. For listing of upgradeable configurations, see Table 2-1: UPS
configurations on page 23.
2.6 Battery system
The battery system provides emergency short-term backup power to safeguard operation during
brownouts, blackouts, and other power interruptions. By default, UPS is configured to use VRLA
batteries. Should there be a need to connect other type of batteries or other energy storage means, a
certified service technician should be consulted prior to proceeding with installation.
93PM 30-50 kW units
The Eaton 93PM 30-50 kW UPS can be equipped with internal batteries to provide a 10-20 min full
load runtime depending on UPS rating. In addition, external battery cabinets can be introduced to the
system to allow extended autonomy. Internal and external batteries can be used in parallel.
93PM 80-200 kW units
The Eaton 93PM 80-200 kW UPS can be equipped with an external battery, and no internal batteries
are available.
For detailed battery specifications, see Chapter 8 Technical data on page 76.
- Eaton 93PM UPS P-164000249 1
- 30-200 kW 1
- Eaton 93PM UPS 3
- Contents 5
- List of Figures 7
- List of Tables 8
- 1 Safety instructions 9
- 2 30-200 kW P-164000249 10
- 1.1 Audience 11
- 1.2 CE marking 11
- 1.3 User precautions 12
- 1.4 Environment 12
- P-164000249 30-200 kW 5 13
- 1.7 For more information 14
- P-164000249 30-200 kW 7 15
- 2 Introduction to Eaton UPS 16
- P-164000249 30-200 kW 9 17
- 10 30-200 kW P-164000249 18
- P-164000249 30-200 kW 11 19
- 12 30-200 kW P-164000249 20
- 2.2 UPS operating modes 21
- 14 30-200 kW P-164000249 22
- Internal relay contacts 22
- P-164000249 30-200 kW 15 23
- 2.2.3 Bypass mode 24
- 2.3 UPS features 25
- 2.3.2 Powerware Hot Sync 26
- 2.4.1 Customer interface 26
- 2.5 Options and accessories 27
- 20 30-200 kW P-164000249 28
- 1. Bypass Input Breaker (BIB) 29
- 2.6 Battery system 30
- P-164000249 30-200 kW 23 31
- 24 30-200 kW P-164000249 32
- 3.2 Site preparations 33
- 26 30-200 kW P-164000249 34
- P-164000249 30-200 kW 27 35
- 28 30-200 kW P-164000249 36
- P-164000249 30-200 kW 29 37
- 30 30-200 kW P-164000249 38
- P-164000249 30-200 kW 31 39
- 32 30-200 kW P-164000249 40
- P-164000249 30-200 kW 33 41
- 34 30-200 kW P-164000249 42
- P-164000249 30-200 kW 35 43
- 4 UPS system installation 44
- P-164000249 30-200 kW 37 45
- 38 30-200 kW P-164000249 46
- Top cable access kit 47
- 40 30-200 kW P-164000249 48
- P-164000249 30-200 kW 41 49
- 42 30-200 kW P-164000249 50
- P-164000249 30-200 kW 43 51
- 44 30-200 kW P-164000249 52
- P-164000249 30-200 kW 45 53
- 46 30-200 kW P-164000249 54
- P-164000249 30-200 kW 47 55
- 4.6.1 Power wiring overview 56
- P-164000249 30-200 kW 49 57
- 50 30-200 kW P-164000249 58
- P-164000249 30-200 kW 51 59
- 52 30-200 kW P-164000249 60
- 5 Communication interfaces 61
- 54 30-200 kW P-164000249 62
- P-164000249 30-200 kW 55 63
- 5.3 Signal input monitoring 64
- P-164000249 30-200 kW 57 65
- 6 UPS operating instructions 66
- P-164000249 30-200 kW 59 67
- 6.1.2 Status indicators 68
- 6.2 Steps to operate the UPS 69
- 6.3 Signing in 70
- STARTING 71
- 64 30-200 kW P-164000249 72
- P-164000249 30-200 kW 65 73
- 66 30-200 kW P-164000249 74
- 6.5 UPS control instructions 75
- 6.6 UPM control instructions 76
- P-164000249 30-200 kW 69 77
- 70 30-200 kW P-164000249 78
- Maintenance Bypass 78
- Switch (MBS) 78
- P-164000249 30-200 kW 71 79
- 7 UPS maintenance 80
- 7.2.1 DAILY maintenance 81
- 7.2.2 MONTHLY maintenance 81
- 7.2.3 PERIODIC maintenance 81
- 7.2.4 ANNUAL maintenance 82
- 7.2.5 BATTERY maintenance 82
- 7.4 Maintenance training 83
- 8 Technical data 84
- 8.2 UPS system input 85
- 8.3 UPS system output 85
- 8.4 Battery specification 86
- P-164000249 30-200 kW 79 87
- 80 30-200 kW P-164000249 88
- 9 Warranty 89
- 10 Installation checklist 90
- P-164000249 30-200 kW 83 91
- 11 APPENDIX A: User settings 92
- Setting Description 93
- Table 11-2: Config settings 93
Related products and manuals for Uninterruptible power supplies (UPSs) Eaton 93PM
(146 pages)
(84 pages)© 2020, manymanuals.com. All rights reserved. | 0.308 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals