Eaton 93PM Installation Guide Page 77
- Page / 93
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
P-164000249 30-200 kW 69
Revision 2 User's and Installation Guide
4. On the UPM control screen, select Shut down module.
6.7 Using the Remote Emergency Power-off switch
A UPS emergency power-off is initiated by the EPO pushbutton switch. In an emergency, you can
use this switch to control the UPS output. The EPO switch de-energizes the critical load and powers
down the UPS immediately, without asking for verification. The UPS, including Bypass, remains off
until restarted.
CAUTION
All power to the critical load is lost when the EPO switch is activated in the following step.
You should use this feature only when you want to de-energize the critical load.
NOTE
The following instructions are for the Eaton Corporation-supplied EPO switch. If a customer-
supplied EPO switch is used, it may not activate in the same manner; refer to the operating
instructions provided with the switch.
To use the EPO switch:
1. Press the EPO pushbutton switch.
The input, output, and bypass backfeed relays open, the battery breaker or disconnect is
tripped, and the power module is turned off immediately, without asking for verification.
DANGER
Do not attempt to restart the system after Load Off until the cause of the shutdown has
been identified and cleared.
2. To restart the UPS after using the EPO pushbutton, reset the EPO switch and then follow the
procedure in Chapter 6.4.1 Starting the UPS system in Double conversion mode on page 63
or Chapter 6.4.2 Starting the UPS system in Bypass mode on page 64.
6.8 Turning UPS from double conversion mode to
mechanical bypass
The operation of the internal MBS is allowed for a trained person only who is familiar with the UPS
behavior and functions. The full UPS wiring diagram with a MBS switch is presented in the installation
instructions.
- Eaton 93PM UPS P-164000249 1
- 30-200 kW 1
- Eaton 93PM UPS 3
- Contents 5
- List of Figures 7
- List of Tables 8
- 1 Safety instructions 9
- 2 30-200 kW P-164000249 10
- 1.1 Audience 11
- 1.2 CE marking 11
- 1.3 User precautions 12
- 1.4 Environment 12
- P-164000249 30-200 kW 5 13
- 1.7 For more information 14
- P-164000249 30-200 kW 7 15
- 2 Introduction to Eaton UPS 16
- P-164000249 30-200 kW 9 17
- 10 30-200 kW P-164000249 18
- P-164000249 30-200 kW 11 19
- 12 30-200 kW P-164000249 20
- 2.2 UPS operating modes 21
- 14 30-200 kW P-164000249 22
- Internal relay contacts 22
- P-164000249 30-200 kW 15 23
- 2.2.3 Bypass mode 24
- 2.3 UPS features 25
- 2.3.2 Powerware Hot Sync 26
- 2.4.1 Customer interface 26
- 2.5 Options and accessories 27
- 20 30-200 kW P-164000249 28
- 1. Bypass Input Breaker (BIB) 29
- 2.6 Battery system 30
- P-164000249 30-200 kW 23 31
- 24 30-200 kW P-164000249 32
- 3.2 Site preparations 33
- 26 30-200 kW P-164000249 34
- P-164000249 30-200 kW 27 35
- 28 30-200 kW P-164000249 36
- P-164000249 30-200 kW 29 37
- 30 30-200 kW P-164000249 38
- P-164000249 30-200 kW 31 39
- 32 30-200 kW P-164000249 40
- P-164000249 30-200 kW 33 41
- 34 30-200 kW P-164000249 42
- P-164000249 30-200 kW 35 43
- 4 UPS system installation 44
- P-164000249 30-200 kW 37 45
- 38 30-200 kW P-164000249 46
- Top cable access kit 47
- 40 30-200 kW P-164000249 48
- P-164000249 30-200 kW 41 49
- 42 30-200 kW P-164000249 50
- P-164000249 30-200 kW 43 51
- 44 30-200 kW P-164000249 52
- P-164000249 30-200 kW 45 53
- 46 30-200 kW P-164000249 54
- P-164000249 30-200 kW 47 55
- 4.6.1 Power wiring overview 56
- P-164000249 30-200 kW 49 57
- 50 30-200 kW P-164000249 58
- P-164000249 30-200 kW 51 59
- 52 30-200 kW P-164000249 60
- 5 Communication interfaces 61
- 54 30-200 kW P-164000249 62
- P-164000249 30-200 kW 55 63
- 5.3 Signal input monitoring 64
- P-164000249 30-200 kW 57 65
- 6 UPS operating instructions 66
- P-164000249 30-200 kW 59 67
- 6.1.2 Status indicators 68
- 6.2 Steps to operate the UPS 69
- 6.3 Signing in 70
- STARTING 71
- 64 30-200 kW P-164000249 72
- P-164000249 30-200 kW 65 73
- 66 30-200 kW P-164000249 74
- 6.5 UPS control instructions 75
- 6.6 UPM control instructions 76
- P-164000249 30-200 kW 69 77
- 70 30-200 kW P-164000249 78
- Maintenance Bypass 78
- Switch (MBS) 78
- P-164000249 30-200 kW 71 79
- 7 UPS maintenance 80
- 7.2.1 DAILY maintenance 81
- 7.2.2 MONTHLY maintenance 81
- 7.2.3 PERIODIC maintenance 81
- 7.2.4 ANNUAL maintenance 82
- 7.2.5 BATTERY maintenance 82
- 7.4 Maintenance training 83
- 8 Technical data 84
- 8.2 UPS system input 85
- 8.3 UPS system output 85
- 8.4 Battery specification 86
- P-164000249 30-200 kW 79 87
- 80 30-200 kW P-164000249 88
- 9 Warranty 89
- 10 Installation checklist 90
- P-164000249 30-200 kW 83 91
- 11 APPENDIX A: User settings 92
- Setting Description 93
- Table 11-2: Config settings 93
Related products and manuals for Uninterruptible power supplies (UPSs) Eaton 93PM
(146 pages)
(84 pages)© 2020, manymanuals.com. All rights reserved. | 1.181 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals