Eaton POWERWARE 9315 Operator's Manual Page 45
- Page / 154
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
INSTALLING OPTIONAL ACCESSORIES
EATON Powerware
®
9315 UPS (500–750 kVA) Installation and Operation Manual S 164201691 Rev 2 www.powerware.com
6-7
6.3 Installing an SCM
The optional SCM shown in Figure 6‐5 provides contacts for monitoring UPS system
status. See Figure A‐29 page A-41 for enclosure dimensions and knockout patterns.
TB2
Surface Mount
(for hanging)
Wires Must be Twisted
Flush Mount
Figure 6‐5. SCM
1. Verify that the UPS system is turned off and all power sources are removed. See
Chapter 9, “UPS Operating Instructions,” for shutdown instructions.
2. Remove the access plate on top of the UPS Input/Rectifier cabinet to gain access
to the customer interface panel (see Figure A‐13 on page A-23).
3. Securely mount the SCM.
4. Install wiring from the SCM using ½” conduit through the cable entry
knockout in the top of the UPS Input/Rectifier cabinet. See Figure A‐13 on
page A-23 for the conduit landing area location.
5. If not already installed, locate the RMP adapter cable assembly in the spare parts
kit (see Figure 6‐6). Mate the DB‐9 connector on the back of the terminal block to
the DB‐9 connector (Port 1) on the UPS customer interface panel (see
Figure A‐19 on page A-30). Use two screws from the spare parts kit to secure
the terminal block bracket to the customer interface panel.
- Powerware 9315 UPS 1
- 500–750 kVA 1
- CONSERVER CES INSTRUCTIONS 2
- Special Symbols 3
- Table of Contents 5
- TABLE OF CONTENTS 6
- List of Figures 9
- LIST OF FIGURES 10
- Chapter 1 Introduction 11
- 1.1 UPS Features 12
- 1.2 Options and Accessories 13
- INTRODUCTION 14
- IMPORTANT SAFETY INSTRUCTIONS 15
- SAVE THESE INSTRUCTIONS 15
- A V E R T I S S E M E N T ! 16
- A T T E N T I O N ! 16
- 1.6 For More Information 16
- 1.7 Getting Help 17
- Section I 19
- Installation 19
- 2.1.1 Preparing Your Site 21
- A R N I N G 26
- INSTALLING THE UPS SYSTEM 27
- 3.7 Installing Accessories 30
- 3.8 Initial Startup 30
- Installation Checklist 32
- Operating Handle 35
- ON Position 35
- OFF Position 35
- 5.1 REPO Installation 37
- 5.2 REPO Operation 38
- S X-Slot cards 39
- 6.1 Installing an RMP 40
- 6.2 Installing an RIM 43
- 6.3 Installing an SCM 45
- Figure 6‐7. SCM TB2 47
- 6.4 Installing X-Slot Cards 48
- Section II 49
- Operation 49
- Battery String 51
- Module Bypass Cabinet (MBC) 51
- Processing Unit 51
- 7.1 Operating Modes 52
- 7.1.1 Normal Mode 53
- 7.1.3 Battery Mode 55
- UNDERSTANDING UPS OPERATION 56
- Figure 8‐1. UPS Control Panel 57
- 8.1 Using the LCD Screen 58
- 8.2 Using the Pushbuttons 59
- 8.3 Adjusting the Contrast 59
- 8.5 Using the Menu Options 60
- 8.5.1 System Meters Screen 61
- 8.5.2 Load Amps Meters Screen 62
- 8.5.6 Unit Statistics Screen 66
- 8.5.7 Mimic Screen 67
- 8.5.8 Time Setup Screen 68
- 8.5.9 Port Setup Screen 69
- USING THE CONTROL PANEL 70
- 9.1.1 Control Panel 72
- 9.1.2 UPS Circuit Breakers 72
- 9.1.3 Emergency UPM Off 72
- 9.2 Starting the UPS 73
- UPS Input Breaker (CB1) OPEN 74
- UPS Output Breaker (CB3) OPEN 74
- UPS Bypass Breaker (CB4) OPEN 74
- UPS OPERATING INSTRUCTIONS 78
- Figure 10‐1. RMP 80
- USING FEATURES AND OPTIONS 81
- Figure 10‐2. RIM 82
- Figure 10‐3. SCM 83
- 11.1 System Event Horns 85
- 11.2 System Event Indicators 85
- 11.3 System Event Messages 85
- RESPONDING TO SYSTEM EVENTS 86
- Chapter 12 Communication 87
- Figure 12‐2. Port 2 (DB‐25) 88
- 12.3.1 Modes 90
- 12.3.2 Rate 90
- 12.3.3 Data/Stop 91
- 12.3.4 Handshaking 91
- 12.3.5 Save 91
- 12.3.6 Default Settings 91
- 12.4 Terminal Mode 92
- 12.4.2 Entire Log [Ctrl]+[P] 93
- COMMUNICATION 94
- 12.5.5 Program Unit Name 97
- 12.5.6 Change Password 97
- 12.5.7 Battery Test Setup 98
- 12.6 Calibration Mode 99
- 12.7 Computer Mode 99
- 12.8 Remote Monitor Mode 99
- 12.9 eNotify Service 100
- 12.10 Remote Notification 101
- 12.11 X-Slot Cards 102
- D A N G E R 103
- W A R N I N G 103
- 13.2.2 Monthly Maintenance 104
- 13.2.3 Annual Maintenance 104
- 13.2.1 Daily Maintenance 104
- C A U T I O N 105
- 13.4 Maintenance Training 105
- MAINTAINING THE UPS SYSTEM 106
- 14.1 Model Numbers 107
- 14.2 UPS System Input 107
- 14.3 UPS System Output 108
- Chapter 15 Warranty 109
- WARRANTY 110
- Appendix A 111
- Installation Reference 111
- INSTALLATION REFERENCE 112
- FRONT VIEW 113
- TOP VIEW 114
- LEFT VIEW 114
- CUSTOMER 120
- INTERFACE 120
- Figure A‐10. Securing Cables 128
- A.4 Location of UPS Terminals 132
- LEFT SIDE 133
- LEFT SIDE FRONT 136
- MBC – TOP AND BUS BARS 137
- Battery Terminal Board 139
- Battery I/O Board 139
- X-SLOT CARD 140
- CUSTOMER INTERFACE 141
- PANEL (X-SLOT) 141
- EATON Powerware 143
- A.6 Typical REPO 146
- Front View 147
- *1642016912* 154
Related products and manuals for Power supply units Eaton POWERWARE 9315
(102 pages)
Power supply units Eaton XT-40 User Manual
(176 pages)
(176 pages)
Power supply units Eaton IT-RSS Setup Guide
(23 pages)
(23 pages)
© 2020, manymanuals.com. All rights reserved. | 0.583 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals