Eaton POWERWARE 9315 Operator's Manual Page 32
- Page / 154
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
INSTALLING THE UPS SYSTEM
EATON Powerware
®
9315 UPS (500–750 kVA) Installation and Operation Manual S 164201691 Rev 2 www.powerware.com
3-8
Installation Checklist
- All packing materials and restraints have been removed from each cabinet.
- Each cabinet in the UPS system is placed in its final installation location.
- A ground bond is installed between any cabinets that are bolted together.
- All switchboards, conduits, and cables are properly routed to the UPS and auxiliary cabinets.
- All power cables are properly sized and terminated.
- A ground conductor is properly installed.
- If a bypass input neutral connection is used, no other N‐G bonds exist downstream from the UPS.
- Battery cables and harnesses are terminated on E4 and E5.
- Internal battery cabinet connections have been completed (bus bars, plugs, etc.).
- Shunt trip signal wiring is connected from UPS to battery breaker(s).
- Air conditioning equipment is installed and operating correctly.
- The area around the UPS system is clean and dust‐free. (It is recommended that the UPS be installed on a level,
sealed concrete pad or floor.)
- Adequate workspace exists around the UPS and other cabinets.
- Adequate lighting is provided around all UPS equipment.
- A 120V service outlet is located within 7.6m (25 ft) of the UPS equipment.
- Each Remote Monitor Panel (RMP) is mounted in its installed location. (OPTIONAL)
- The control wiring for each RMP is terminated inside the UPS cabinet. (OPTIONAL)
- The remote emergency power-off (REPO) device is mounted in its installed location and its wiring terminated inside
the UPS cabinet. (OPTIONAL)
- Summary alarms and/or building alarms are wired appropriately. (OPTIONAL)
- A Relay Interface Module (RIM) is mounted in its installed location and its wiring is terminated inside the UPS cabinet.
(OPTIONAL)
- A remote battery disconnect control is mounted in its installed location and its wiring is terminated inside the UPS and
battery cabinets. (OPTIONAL)
- Circuit breakers with adjustable trip mechanisms adjusted to match site requirements.
- Debris shields covering ventilation grills are removed from all cabinets.
- Startup and operational checks are performed by an authorized Eaton Customer Service Engineer.
- Powerware 9315 UPS 1
- 500–750 kVA 1
- CONSERVER CES INSTRUCTIONS 2
- Special Symbols 3
- Table of Contents 5
- TABLE OF CONTENTS 6
- List of Figures 9
- LIST OF FIGURES 10
- Chapter 1 Introduction 11
- 1.1 UPS Features 12
- 1.2 Options and Accessories 13
- INTRODUCTION 14
- IMPORTANT SAFETY INSTRUCTIONS 15
- SAVE THESE INSTRUCTIONS 15
- A V E R T I S S E M E N T ! 16
- A T T E N T I O N ! 16
- 1.6 For More Information 16
- 1.7 Getting Help 17
- Section I 19
- Installation 19
- 2.1.1 Preparing Your Site 21
- A R N I N G 26
- INSTALLING THE UPS SYSTEM 27
- 3.7 Installing Accessories 30
- 3.8 Initial Startup 30
- Installation Checklist 32
- Operating Handle 35
- ON Position 35
- OFF Position 35
- 5.1 REPO Installation 37
- 5.2 REPO Operation 38
- S X-Slot cards 39
- 6.1 Installing an RMP 40
- 6.2 Installing an RIM 43
- 6.3 Installing an SCM 45
- Figure 6‐7. SCM TB2 47
- 6.4 Installing X-Slot Cards 48
- Section II 49
- Operation 49
- Battery String 51
- Module Bypass Cabinet (MBC) 51
- Processing Unit 51
- 7.1 Operating Modes 52
- 7.1.1 Normal Mode 53
- 7.1.3 Battery Mode 55
- UNDERSTANDING UPS OPERATION 56
- Figure 8‐1. UPS Control Panel 57
- 8.1 Using the LCD Screen 58
- 8.2 Using the Pushbuttons 59
- 8.3 Adjusting the Contrast 59
- 8.5 Using the Menu Options 60
- 8.5.1 System Meters Screen 61
- 8.5.2 Load Amps Meters Screen 62
- 8.5.6 Unit Statistics Screen 66
- 8.5.7 Mimic Screen 67
- 8.5.8 Time Setup Screen 68
- 8.5.9 Port Setup Screen 69
- USING THE CONTROL PANEL 70
- 9.1.1 Control Panel 72
- 9.1.2 UPS Circuit Breakers 72
- 9.1.3 Emergency UPM Off 72
- 9.2 Starting the UPS 73
- UPS Input Breaker (CB1) OPEN 74
- UPS Output Breaker (CB3) OPEN 74
- UPS Bypass Breaker (CB4) OPEN 74
- UPS OPERATING INSTRUCTIONS 78
- Figure 10‐1. RMP 80
- USING FEATURES AND OPTIONS 81
- Figure 10‐2. RIM 82
- Figure 10‐3. SCM 83
- 11.1 System Event Horns 85
- 11.2 System Event Indicators 85
- 11.3 System Event Messages 85
- RESPONDING TO SYSTEM EVENTS 86
- Chapter 12 Communication 87
- Figure 12‐2. Port 2 (DB‐25) 88
- 12.3.1 Modes 90
- 12.3.2 Rate 90
- 12.3.3 Data/Stop 91
- 12.3.4 Handshaking 91
- 12.3.5 Save 91
- 12.3.6 Default Settings 91
- 12.4 Terminal Mode 92
- 12.4.2 Entire Log [Ctrl]+[P] 93
- COMMUNICATION 94
- 12.5.5 Program Unit Name 97
- 12.5.6 Change Password 97
- 12.5.7 Battery Test Setup 98
- 12.6 Calibration Mode 99
- 12.7 Computer Mode 99
- 12.8 Remote Monitor Mode 99
- 12.9 eNotify Service 100
- 12.10 Remote Notification 101
- 12.11 X-Slot Cards 102
- D A N G E R 103
- W A R N I N G 103
- 13.2.2 Monthly Maintenance 104
- 13.2.3 Annual Maintenance 104
- 13.2.1 Daily Maintenance 104
- C A U T I O N 105
- 13.4 Maintenance Training 105
- MAINTAINING THE UPS SYSTEM 106
- 14.1 Model Numbers 107
- 14.2 UPS System Input 107
- 14.3 UPS System Output 108
- Chapter 15 Warranty 109
- WARRANTY 110
- Appendix A 111
- Installation Reference 111
- INSTALLATION REFERENCE 112
- FRONT VIEW 113
- TOP VIEW 114
- LEFT VIEW 114
- CUSTOMER 120
- INTERFACE 120
- Figure A‐10. Securing Cables 128
- A.4 Location of UPS Terminals 132
- LEFT SIDE 133
- LEFT SIDE FRONT 136
- MBC – TOP AND BUS BARS 137
- Battery Terminal Board 139
- Battery I/O Board 139
- X-SLOT CARD 140
- CUSTOMER INTERFACE 141
- PANEL (X-SLOT) 141
- EATON Powerware 143
- A.6 Typical REPO 146
- Front View 147
- *1642016912* 154
Related products and manuals for Power supply units Eaton POWERWARE 9315
(102 pages)
Power supply units Eaton XT-40 User Manual
(176 pages)
(176 pages)
Power supply units Eaton IT-RSS Setup Guide
(23 pages)
(23 pages)
© 2020, manymanuals.com. All rights reserved. | 1.989 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals