Eaton POWERWARE 9315 Instruction Manual Page 26
- Page / 206
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
2−4
EATON Powerware 9315 Parallel Capacity/Redundant System
164201150 Rev. E www.powerware.com
2.6 Installing SMB Wiring
1. Install power wiring between the SBM, SMB, and critical load. Refer to
Appendix A of this manual for wiring and termination requirements and wiring
access information.
2. Install control wiring between the SBM and SMB. Refer to Appendix A of this
manual for wiring and termination requirements and wiring access information.
2.7 Prepare for Installing Optional Accessories
If you are installing optional accessories, such as a Remote Monitor Panel (RMP),
a Relay Interface Module (RIM), a Supervisory Contact Module (SCM), or a Remote
Emergency Power Off (EPO), you must install conduit between each device and the
UPS cabinet for wiring these options. Refer to Appendix A for the locations of the
interface points within the SBM cabinet.
2.7.1 To Prepare the SBM for Wiring to an RMP, RIM, SCM, or
Remote EPO:
1. Be sure the Parallel Capacity/Redundant system is turned off and all power
sources are removed. (See the operation section of this manual for shutdown
instructions.)
2. Remove the access plate on top of the SBM cabinet to gain access to the
Customer Interface Panel (refer to Appendix A for location of the access plate).
3. Refer to Chapters 3, 4, 5, or 6 as applicable for installation instructions.
2.8 Initial Startup
Startup and operational checks should be performed only by authorized service
personnel. Contact service in advance (usually a two week notice is required) to
reserve a preferred startup date.
2.9 Completing the Installation Checklist
The final step in installing your Parallel Capacity/Redundant system is completing
the following Installation Checklist. This checklist ensures that you have
completely installed all hardware, cables, and other equipment. Completing all
items listed on the checklist will ensure a smooth installation. You should make a
copy of the Installation Checklist before filling it out, and retain the original.
After your installation is complete, a service representative will be able to verify the
operation of your Parallel Capacity/Redundant system and commission it to
support your critical load. The service representative cannot perform any
installation tasks other than verifying software and operating setup parameters.
Service personnel may request a copy of the completed Installation Checklist to be
sure you have completed all applicable equipment installation.
NOTE: The Installation Checklist MUST be completed prior to starting the Parallel
Capacity/Redundant system for the first time.
- Powerware 9315 UPS 1
- Table of Contents 3
- Section IIOperation 4
- List of Figures 8
- Introduction 11
- Basic System Configurations 13
- Using This Manual 13
- Safety Considerations 15
- For More Information 16
- Getting Help 16
- Section I 17
- Installation 17
- Getting Started 19
- 1.1.2 Preparing Your Site 20
- Installing the Parallel 23
- 2.5 Installing SBM Wiring 25
- 2.6 Installing SMB Wiring 26
- 2.8 Initial Startup 26
- 2.10 Installation Checklist 27
- EMERGENCY OFF 29
- UNINTERRUPTIBLE POWER SYSTEM 29
- Installing a Remote 31
- Monitor Panel (Optional) 31
- WIRES MUST 32
- BE TWISTED 32
- 4.2 To install an RMP: 33
- Installing a Relay 35
- Interface Module (Optional) 35
- 5.2 To install a RIM: 36
- Installing a Supervisory 39
- Contact Module 39
- 1. Securely mount the SCM 40
- Section II 43
- Operation 43
- Understanding Parallel 45
- Operation: 46
- 7.2.1 Normal Mode 47
- 7.2.2 Bypass Mode 48
- 7.2.3 Battery Mode 49
- Path of Electrical Power 51
- Operational Controls 55
- 8.2.3 EMERGENCY UPM OFF 56
- 8.2.6 Installation Features 56
- 8.3 Options and Accessories 57
- 8.4 Safety Considerations 60
- Using the SBM Control Panel 63
- 9.2 Using the LCD Screen 64
- 9.3 Using the Pushbuttons 65
- 9.4 Adjusting the Contrast 65
- 9.6 Using the Menu Options 67
- KWA KV Amps/Phase 73
- CAPACITY 73
- 500 420 222 73
- 10.2 Operation of SBM with 77
- 10.2.2 Manual Start 78
- 10.2.3 Auto Start 79
- 10.2.4 Single UPM Shutdown 80
- 10.2.5 SBM Shutdown to Bypass 80
- 10.3 Operation of SBM with 84
- 10.3.2 Manual Start 85
- 10.3.3 Auto Start 86
- 10.3.4 Single UPM Shutdown 86
- 10.3.5 SBM Shutdown to Bypass 87
- EMERGENCY UPM OFF 90
- Using Features and Options 93
- 11.7 Common Battery Racks 98
- Responding to System Events 99
- 12.4 System Event Messages 100
- Serial Communications 107
- PORT 1 (DB−9) 108
- PORT 2 (DB−25) 109
- 13.4.1 Modes 111
- 13.4.2 Rate 111
- 13.4.4 Handshaking 112
- 13.4.5 Save 112
- 13.4.6 Default Settings 112
- 13.4.3 Data/Stop 112
- 13.5 Terminal Mode 113
- 13.5.2 Entire Log (Ctrl + P) 114
- 13.6 System Configuration 116
- 13.6.5 Program Unit Name 119
- 13.6.6 Change Password 119
- 13.6.7 Battery Test Setup 120
- 13.7 Calibration Mode 121
- 13.8 Computer Mode 121
- 13.9 Remote Monitor Mode 121
- Remote Notification 123
- 14.3 Description of Operation 124
- 14.3.2 Call Out 125
- 14.4 Hardware Requirements 126
- 14.5 Configuring the Modem 127
- 14.6 SBM Setup Configuration 131
- 14.6.1 User Selected Events 132
- Maintaining the Parallel 137
- Capacity/Redundant System 137
- 15.4 Maintenance Training 140
- Product Specifications 141
- 16.3 SBM Output 142
- DESCRIPTION: 146
- DRAWING NO: 146
- SEPARATE BATTERY SYSTEM 150
- COMMON BATTERY SYSTEM 151
- SEPARATE BATTERY PARALLEL 154
- CAPACITY/REDUNDANT 154
- See Sheet 3 for notes 154
- COMMON BATTERY PARALLEL 155
- 1200A SBM FRONT VIEW 157
- 1200A SBM TOP VIEW 158
- 1200A SBM SIDE VIEW 158
- FRONT VIEW 163
- SIDE VIEW 164
- TOP VIEW 164
- 2000A SBM FRONT VIEW 168
- 2000A SBM TOP VIEW 169
- 2000A SBM SIDE VIEW 169
- REAR VIEW 171
- Customer Interface Panel 182
- 1200 and 2000 Amp SBM 182
- Top View 182
- 1200 and 2000 AMP SBM 183
- TYPICAL POWERNET NETWORK 183
- WIRING AND TERMINATIONS 183
- Terminating Resistor Location 184
- DRAWING NO: SHEET: 185
- CONTACT RATING: 188
- UPM Powernet Interface Panel 189
- SBM CUSTOMER INTERFACE PANEL 190
- 164201150−14 190
- UPM CAN INTERFACE: 193
- POWERWARE 9315−625/750 UPMs 193
- 164201150−15 193
- UPS PRODUCTS 203
- *164201150E* 206
Related products and manuals for Power supply units Eaton POWERWARE 9315
Power supply units Eaton IT-RSS Setup Guide
(23 pages)
(23 pages)
(29 pages)© 2020, manymanuals.com. All rights reserved. | 0.221 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals