Eaton POWERWARE 9315 Instruction Manual Page 183
- Page / 206
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
A−41
EATON Powerware 9315 Parallel Capacity/Redundant System
164201150 Rev. E www.powerware.com
DESCRIPTION:
DRAWING NO: SHEET:
SBM CUSTOMER INTERFACE PANEL
2 of 7
1200 and 2000 AMP SBM
UPM
1
UPM
2
UPM
3
UPM
4
SBM
TERMINATION
POINTS
TERMINATION
POINTS
TYPICAL POWERNET NETWORK
Arrangement A
164201150−13
CHANNEL A
CHANNEL B
UPM
1
UPM
2
UPM
3
UPM
4
SBM
TERMINATION
POINTS
TERMINATION
POINTS
Arrangement B
CHANNEL A
CHANNEL B
UPM
1
UPM
2
UPM
3
UPM
4
SBM
TERMINATION
POINT
TERMINATION
POINTS
Arrangement C (Robust Network Routing)
CHANNEL A
CHANNEL B
WIRING AND TERMINATIONS
CHAN B
TERMINATION
POINT
CHAN A
- Powerware 9315 UPS 1
- Table of Contents 3
- Section IIOperation 4
- List of Figures 8
- Introduction 11
- Basic System Configurations 13
- Using This Manual 13
- Safety Considerations 15
- For More Information 16
- Getting Help 16
- Section I 17
- Installation 17
- Getting Started 19
- 1.1.2 Preparing Your Site 20
- Installing the Parallel 23
- 2.5 Installing SBM Wiring 25
- 2.6 Installing SMB Wiring 26
- 2.8 Initial Startup 26
- 2.10 Installation Checklist 27
- EMERGENCY OFF 29
- UNINTERRUPTIBLE POWER SYSTEM 29
- Installing a Remote 31
- Monitor Panel (Optional) 31
- WIRES MUST 32
- BE TWISTED 32
- 4.2 To install an RMP: 33
- Installing a Relay 35
- Interface Module (Optional) 35
- 5.2 To install a RIM: 36
- Installing a Supervisory 39
- Contact Module 39
- 1. Securely mount the SCM 40
- Section II 43
- Operation 43
- Understanding Parallel 45
- Operation: 46
- 7.2.1 Normal Mode 47
- 7.2.2 Bypass Mode 48
- 7.2.3 Battery Mode 49
- Path of Electrical Power 51
- Operational Controls 55
- 8.2.3 EMERGENCY UPM OFF 56
- 8.2.6 Installation Features 56
- 8.3 Options and Accessories 57
- 8.4 Safety Considerations 60
- Using the SBM Control Panel 63
- 9.2 Using the LCD Screen 64
- 9.3 Using the Pushbuttons 65
- 9.4 Adjusting the Contrast 65
- 9.6 Using the Menu Options 67
- KWA KV Amps/Phase 73
- CAPACITY 73
- 500 420 222 73
- 10.2 Operation of SBM with 77
- 10.2.2 Manual Start 78
- 10.2.3 Auto Start 79
- 10.2.4 Single UPM Shutdown 80
- 10.2.5 SBM Shutdown to Bypass 80
- 10.3 Operation of SBM with 84
- 10.3.2 Manual Start 85
- 10.3.3 Auto Start 86
- 10.3.4 Single UPM Shutdown 86
- 10.3.5 SBM Shutdown to Bypass 87
- EMERGENCY UPM OFF 90
- Using Features and Options 93
- 11.7 Common Battery Racks 98
- Responding to System Events 99
- 12.4 System Event Messages 100
- Serial Communications 107
- PORT 1 (DB−9) 108
- PORT 2 (DB−25) 109
- 13.4.1 Modes 111
- 13.4.2 Rate 111
- 13.4.4 Handshaking 112
- 13.4.5 Save 112
- 13.4.6 Default Settings 112
- 13.4.3 Data/Stop 112
- 13.5 Terminal Mode 113
- 13.5.2 Entire Log (Ctrl + P) 114
- 13.6 System Configuration 116
- 13.6.5 Program Unit Name 119
- 13.6.6 Change Password 119
- 13.6.7 Battery Test Setup 120
- 13.7 Calibration Mode 121
- 13.8 Computer Mode 121
- 13.9 Remote Monitor Mode 121
- Remote Notification 123
- 14.3 Description of Operation 124
- 14.3.2 Call Out 125
- 14.4 Hardware Requirements 126
- 14.5 Configuring the Modem 127
- 14.6 SBM Setup Configuration 131
- 14.6.1 User Selected Events 132
- Maintaining the Parallel 137
- Capacity/Redundant System 137
- 15.4 Maintenance Training 140
- Product Specifications 141
- 16.3 SBM Output 142
- DESCRIPTION: 146
- DRAWING NO: 146
- SEPARATE BATTERY SYSTEM 150
- COMMON BATTERY SYSTEM 151
- SEPARATE BATTERY PARALLEL 154
- CAPACITY/REDUNDANT 154
- See Sheet 3 for notes 154
- COMMON BATTERY PARALLEL 155
- 1200A SBM FRONT VIEW 157
- 1200A SBM TOP VIEW 158
- 1200A SBM SIDE VIEW 158
- FRONT VIEW 163
- SIDE VIEW 164
- TOP VIEW 164
- 2000A SBM FRONT VIEW 168
- 2000A SBM TOP VIEW 169
- 2000A SBM SIDE VIEW 169
- REAR VIEW 171
- Customer Interface Panel 182
- 1200 and 2000 Amp SBM 182
- Top View 182
- 1200 and 2000 AMP SBM 183
- TYPICAL POWERNET NETWORK 183
- WIRING AND TERMINATIONS 183
- Terminating Resistor Location 184
- DRAWING NO: SHEET: 185
- CONTACT RATING: 188
- UPM Powernet Interface Panel 189
- SBM CUSTOMER INTERFACE PANEL 190
- 164201150−14 190
- UPM CAN INTERFACE: 193
- POWERWARE 9315−625/750 UPMs 193
- 164201150−15 193
- UPS PRODUCTS 203
- *164201150E* 206
Related products and manuals for Power supply units Eaton POWERWARE 9315
Power supply units Eaton IT-RSS Setup Guide
(23 pages)
(23 pages)
(29 pages)© 2020, manymanuals.com. All rights reserved. | 0.327 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals