Eaton Power Xpert Gateway Series 1000 Card User's Guide download pdf (Page 105)

Volume 3—Power Distribution and Control Assemblies CA08100004E—November 2013 www.eaton.com V3-T9-105

9.3

Metering Devices, Protective Relays, Software and Connectivity

Metering Devices

PXMP meter modules (PXMP-MMs)

Compatible with all PXMP Meter Base slots 1–10 LED

indicators:

●

Health and status green, blink to show activity

●

Pulse energy output one red per group of three loads

●

Load energy direction red/green pair per load

All variations support six load inputs.

Current sensor connection is one 2 x 2 connector per load.

Compatible with PXMP-SCXX sensor cables, total cable length

to the sensor should not exceed 28 ft (8.5m).

Note that -AB suffix only affects what voltage channels the loads

are paired with for metering purposes.

PXMP-MM10MA supports the CSXXX series of 10 mA

maximum secondary output current transformers.

PXMP-MM100MA supports the PXMP-CSXXX series of 100 mA

maximum secondary output current transformers.

PXMP-MM333MV supports 333 mV maximum secondary

output current transformers with the use of the PXMP-

IM333MV interface module.

PXMP digital output module (PXMP-DOM)

●

Compatible with all PXMP-MB slots 1–10

●

LED indicators

●

Health and status green, blink to show activity

●

Output On/Off status one green per output

●

Eight individual solid-state relay outputs

●

Each circuit rated for 24 Vdc (±20%) with an 80 mA load

maximum

●

24 Vdc is externally sourced

●

Group isolation to ground 2 kV

●

Each circuit has its own separate common, circuit-to-circuit

isolation 120V

●

16-position removable terminal plug

●

12–18 AWG (3.31–0.82 mm

), wire ferrules recommended

PXMP pulse input modules (PXMP-PIMs)

●

Compatible with all PXMP-MB slots 1–10

●

LED indicators

●

Health and status green, blink to show activity

●

Input On/Off status one green per pulse input

●

Eight pulse inputs to external dry contacts

●

Maximum pulse rate is 20 Hz

●

Minimum pulse width is 20 milliseconds

●

External circuit groups rated for 24 Vdc (±20%)

●

All circuits share the same electrical common

●

External supply connects to the module with a two-position

removable terminal plug

●

The supply is internally fanned out to all circuits

●

Group isolation limited to 300V to ground due to TVS diode

clamp

●

Input impedance ~2.2K causing a 10 mA load per input when

energized

●

External circuit groups connect with a 16-position removable

terminal plug

●

Terminals support 12–18 AWG (3.31–0.82 mm

), wire

ferrules recommended

PXMP energy portal module (PXMP-EPM)

●

Only functionally compatible with PXMP-MB slot 10

●

LED indicators

●

Top health and status green, blink to show activity

●

Com. reset button—reset to defaults

●

Local IP 192/10

●

RJ45 front-facing Ethernet configuration port LEDs

– Link (Tx/Rx blink)

– 10/100 speed

●

LED four-stack for bottom LAN/WAN Ethernet port

●

Link (Tx/Rx blink)

●

10/100 speed

●

DHCP/Fixed

●

TX active

●

Config. Ethernet RJ45 Cat5 STP/UTP

●

10Base-T/100Base-Tx

●

Auto crossover capability supported

●

Java Web browser interface

●

Bottom facing LAN/WAN Ethernet port

●

RJ45 Cat5 STP/UTP 10Base-T/100Base-Tx

●

STP required for full electromagnetic immunity

●

Auto crossover capability supported

●

Supports Modbus TCP and Java Web browser interface

●

Bottom-facing telephone modem interface

●

Modem type V92/56K baud

●

RJ11 field interface

1 2 ... 100 101 102 103 104 105 106 107 108 109 110 ... 298 299

Comments to this Manuals

No comments

Eaton Power Xpert Gateway Series 1000 Card User's Guide Page 105

Comments to this Manuals

Related products and manuals for Networking Eaton Power Xpert Gateway Series 1000 Card